View MCL2AJTTE100_4565903.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SS-223 R9
AHA 12/06/06
Multi Layer Ferrite Inductors Type MCL
1. General
Monolithic structure for closed magnetic path eliminates
CERTIFIED
CERTIFIED
crosstalk and provides high reliability in a wide range of temperature and humidity ranges Standard EIA packages: 1J, 2A, 2B
Nickel barrier with solder overcoat for excellent solderability Magnetically shielded
2. 2.1 Dimensions
L
W Solder Plating Ni Plating Silver Metallization d
Size Code 1J (0603) 2A (0805) 2B (1206)
L .063.006 (1.60.15) .079.008 (2.00.2) .126.008 (3.20.2)
W .031.006 (0.80.15) .049.008 (1.250.2) .063.008 (1.60.2)
t .031.006 (0.80.15) .035.008 (0.90.2) .043.008 (1.10.2)
d .014.006 (0.360.15) .02.01 (0.510.25) .02.01 (0.510.25)
t
Terminations (Metallization Bands)
d
Electrodes
3. Ordering and Specifying Information*
MCL
Type
1J
Size
1J 2A 2B
H
Material
Permeability Code: H J
T
Termination Material
T: Sn (Other termination styles available, contact factory for options)
TE
Packaging
TD: 7" Paper Tape (1J - 4,000 pcs/reel; 2A - 0.047H - 2.2H = 4,000 pcs/reel) TE: 7" Embossed Plastic (2A - 2.7H - 10H = 3,000 pcs/reel; 2B - 3,000 pcs/reel)
R10
Nominal Inductance
047 = .047H R10 = .100H
J
Tolerance
K: 10% M: 20%
* Please note: KSE's part numbers do not contain any spaces or hyphens.
4. Standard Applications
Part Designation MCL1JHTTD047M MCL1JHTTD068M MCL1JHTTD082M MCL1JHTTDR10* MCL1JHTTDR12* MCL1JHTTDR15* MCL1JHTTDR18* MCL1JHTTDR22* MCL1JHTTDR27* Inductance L (H) 0.047 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 Minimum Q L.Q. Test Frequency (MHz) 50 Self Resonant Frequency Typical (MHz) 260 250 245 240 205 180 165 150 136 DC Resistance Maximum () 0.30 -55C to +125C Allowable DC Current Maximum (mA) Operating Temperature Range
10
0.50 0.60 0.80
50
15
25
* Add tolerance character (K, M) - Other tolerances available upon request
PAGE 1 OF 6 814-362-5536
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
Fax 814-362-8883
www.koaspeer.com
Spec ific ation s g iven herein m ay be cha nged a t any tim e w itho ut pr ior not ice. Pleas e c onf ir m te chnic al s pec if ica tions before you order an d/or u se.
SS-223 R9
4. Standard Applications (continued)
Part Designation MCL1JHTTDR33* MCL1JHTTDR39* MCL1JHTTDR47* MCL1JHTTDR56* MCL1JHTTDR68* MCL1JHTTDR82* MCL1JJTTD1R0* MCL1JJTTD1R2* MCL1JJTTD1R5* MCL1JJTTD1R8* MCL1JJTTD2R2* MCL1JJTTD2R7* MCL1JJTTD3R3* MCL1JJTTD3R9* MCL1JJTTD4R7* MCL1JJTTD5R6* MCL1JJTTD6R8* MCL1JJTTD8R2* MCL1JJTTD100* MCL1JJTTD120* MCL2AHTTD047M MCL2AHTTD068M MCL2AHTTD082M MCL2AHTTDR10* MCL2AHTTDR12* MCL2AHTTDR15* MCL2AHTTDR18* MCL2AHTTDR22* MCL2AHTTDR27* MCL2AHTTDR33* MCL2AHTTDR39* MCL2AHTTDR47* MCL2AHTTDR56* MCL2AHTTDR68* MCL2AHTTDR82* MCL2AJTTD1R0* MCL2AJTTD1R2* MCL2AJTTD1R5* MCL2AJTTD1R8* MCL2AJTTD2R2* MCL2AJTTE2R7* MCL2AJTTE3R3* MCL2AJTTE3R9* MCL2AJTTE4R7* Inductance L (H) 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 0.047 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 Minimum Q L.Q. Test Frequency (MHz) Self Resonant Frequency Typical (MHz) 125 110 105 95 90 85 75 65 60 55 50 45 40 35 33 22 20 18 17 15 320 280 255 235 220 200 185 170 150 145 135 125 115 105 100 75 65 60 55 50 45 41 38 35 DC Resistance Maximum () 0.85 1.00 1.35 1.55 1.70 2.10 0.60 0.80 0.95 1.15 1.35 1.55 1.70 2.10 1.55 1.70 2.10 1.85 2.10 0.20 Allowable DC Current Maximum (mA) Operating Temperature Range
15
25
35
25 -55C to +125C 15
10 35
4
5
30
2
3
15
50
300
0.30 0.40 0.50 0.55 0.65 0.75 0.80 1.00 0.40 0.50 0.60 0.65 0.75 0.80 0.90 1.00 200 -55C to +125C
20
250
25
25
150
50
45
10
30
* Add tolerance character (K, M) - Other tolerances available upon request
PAGE 2 OF 6 Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Spec ific ation s g iven herein m ay be cha nged a t any tim e w itho ut pr ior not ice. Pleas e c onf ir m te chnic al s pec if ica tions before you order an d/or u se.
SS-223 R9
4. Standard Applications (continued)
Part Designation MCL2AJTTE5R6* MCL2AJTTE6R8* MCL2AJTTE8R2* MCL2AJTTE100* MCL2BHTTE047M MCL2BHTTE068M MCL2BHTTER10* MCL2BHTTER12* MCL2BHTTER15* MCL2BHTTER18* MCL2BHTTER22* MCL2BHTTER27* MCL2BHTTER33* MCL2BHTTER39* MCL2BHTTER47* MCL2BHTTER56* MCL2BHTTER68* MCL2BHTTER82* MCL2BJTTE1R0* MCL2BJTTE1R2* MCL2BJTTE1R5* MCL2BJTTE1R8* MCL2BJTTE2R2* MCL2BJTTE2R7* MCL2BJTTE3R3* MCL2BJTTE3R9* MCL2BJTTE4R7* MCL2BJTTE5R6* MCL2BJTTE6R8* MCL2BJTTE8R2* MCL2BJTTE100* MCL2BJTTE120* MCL2BJTTE150* MCL2BJTTE180* MCL2BJTTE220* MCL2BJTTE270* MCL2BJTTE330* Inductance L (H) 5.6 6.8 8.2 10 0.047 0.068 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 Minimum Q L.Q. Test Frequency (MHz) 4 2 50 Self Resonant Frequency Typical (MHz) 32 29 26 24 320 280 235 220 200 185 170 150 145 135 125 115 105 100 75 65 60 55 50 45 41 38 35 32 29 26 24 22 19 18 16 14 13 DC Resistance Maximum () 0.90 1.00 1.10 1.15 0.15 0.25 0.30 0.40 0.50 0.60 0.50 0.60 0.70 0.80 0.90 0.40 0.50 250 Allowable DC Current Maximum (mA) Operating Temperature Range -55C to +125C
50
15
300
20
25
200
25
150
100
-55C to +125C
45
10
0.60 50 0.70 0.80 0.85 0.90 1.00 1.05 0.70 0.90 1.05 5
4 50 2
25
15
30
1 0.4
* Add tolerance character (K, M) - Other tolerances available upon request
PAGE 3 OF 6 Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Spe cific at io ns g ive n herein m ay be ch anged a t any tim e w ith out p rior not ice. Pleas e c onf ir m t echn ic al s pec ifica tions before you order an d/or u se.
SS-223 R9
5. Characteristics
Item Operating Temperature Storage Temperature Requirement -25C ~ +85C 40C @ 70% Humidity Sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. Flux: 5-10 sec dip After Flux: Air dry for 15 sec Preheat: 150C 10C Preheat Time: 60 sec Solder Temp: 260C 5C Dip Time: 10 1 sec Flux: 5-10 sec dip After Flux: Air dry for 15 sec Solder Temp: 245C 5C Dip Time: 5 0.5 sec The bead shall be subjected to the following 5 steps for the period of time shown below. The 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) Flux: 5-10 sec 2) After Flux: Air dry for 15 sec 3) Solder Temp: 230C 5C 4) Dip Time: 5 0.5 sec 5) Cool: Air cool for 60 seconds Conditions
Resistance to Solder Heat
Change in Inductance: Relative to value before test 20%. Appearance: There shall be no cracking Solder Coverage: More than 75% of the terminal electrode shall be covered with solder. Solder Coverage: More than 95% of the termination shall be covered with solder.
Solderability
Leach Resistance
Appearance: There shall be no visible signs of physical or mechanical damage (i.e. no cracks) Terminations: Termination must not be leached away for more than 5%.
Insulation Resistance Solvent Resistance
Insulation Resistance: Min 1G ohms Change in Inductance: Relative to value before test 10%. Cleaning by: Washer: Ultrasonic washer (100W) Solvent: Isopropyl alcohol Time: 3 minutes Type 1J (0603) 2A (0805) 2B (1206) Type 1J (0603) 2A (0805) 2B (1206) W(kgf) 0.5 1.0 1.5 W(kgf) 1.4 1.8 2.3 Time 30 sec 2 sec 30 sec 2 sec 30 sec 2 sec Time 60 sec 60 sec 60 sec
Terminal Strength (hanging test)
Appearance: The terminal electrode shall not break off, nor shall there be damage to the body.
Terminal Strength (push test)
Appearance: There shall be no evidence of mechanical degradations to terminals or body.
Bending Strength
Appearance: There shall be no physical or mechanical damage Inductance: Relative to initial value before test 10%
Board: 90x40x1.6mm Bend: 1mm Time: 5 sec
PAGE 4 OF 6 Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Spec ific ation s g iven herein m ay be cha nged a t any tim e w itho ut pr ior not ice. Pleas e c onf ir m te chnic al s pec if ica tions before you order an d/or u se.
SS-223 R9
5. Characteristics (continued)
Item Mechanical Shock Requirement Appearance: There shall be no physical or mechanical damage Inductance: Relative to initial value before test 10% Inductance: Relative to initial value 10% Conditions Force: 50G Time: 11 msec There shall be 3 shocks in each of 6 directions (18 shocks total). Only endurance conditioning by sweeping shall be made. The entire frequency range from 10-2,000 Hz and return to 10 Hz in 20 minutes (this shall constitute one cycle). Amplitude: 1.5mm The test shall have a 15G peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours). Step 1-start 2-hold 3-transfer 4-hold 5-transfer Temperature -40C 2C -40C 2C -- +105C 2C -- Time -- 30 min 5 min 0.5 min max. 30 min 5 min 0.5 min max.
Vibration
Thermal Shock
Appearance: There shall be no physical or mechanical damage. Inductance: Relative to initial value 20%. DCR: The DCR shall not exceed initial specified value. Testing of the parts will be made at 0 hours, 250 hours and 500 hours. Before testing the parts shall be allowed to cool to room temperature for 24 hours.
Steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. Temperature: 85C 2C Relative Humidity: 85% Time: 1,000 hours total Apply: 100% rated current
Load Humidity
Appearance: There shall be no physical or mechanical damage Inductance: Relative to initial value 15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above.
Life Test
Appearance: There shall be no physical or mechanical damage Inductance: Relative to initial value 15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above.
Temperature: 85C 2C Time: 1,000 hours total Apply: 100% rated current
6. Packaging Specifications KOA's multi layer components are provided on tape-and-reel for use in pick-and-place machines. The reel size is 7 inch.
PAGE 5 OF 6 Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Spec ific ation s g iven herein m ay be cha nged a t any tim e w itho ut pr ior not ice. Pleas e c onf ir m te chnic al s pec if ica tions before you order an d/or u se.
SS-223 R9
7. Dimensions - inches (mm)
Tape 1J 2A 2B Ao Bo Ko
E F
Do
Po
P2
t
0.0430.002 0.0750.002 0.0430.002 (1.10.1) (1.90.1) (1.10.1) 0.0630.002 0.0930.002 0.0460.002 (1.60.1) (2.40.1) (1.20.1) 0.0710.002 0.1380.002 0.0480.002 (1.80.1) (3.50.1) (1.20.1)
W
Bo
D1
P1
Ao
Ko
Tape 1J 2A 2B
E
F
W
P1
Po
P2
Do
D1
t 0.0090.001 (0.230.02)
0.0690.004 0.1380.002 0.3180.002 0.1570.004 0.1570.004 0.0790.002 0.0590.004 0.039 min. (1.750.10) (3.50.005) (8.10.1) (4.00.1) (4.00.1) (2.000.05) (1.5+0.1/-0.0) (1.0 min.)
8. Chip Quantities Per Reel
Chip Size 1J 2A 2B Parts on 7 inch (178mm) Reel 4,000 * 2,000/4,000 3,000
9. Recommended PC Board Land Patterns - inches (mm)
Chip Size 1J 2A 2B L 0.102 (2.6) 0.118 (3.0) 0.173 (4.4) G 0.022 (0.55) 0.026 (0.66) 0.059 (1.5) H 0.037 (0.94) 0.057 (1.45) 0.071 (1.8)
* MCL0805: 2.7H ~ 12H = 2K 0.047H ~ 2.2H = 4K
G L
H
10. Recommended Temperature Profiles for Soldering
Recommended Temperature Profile Recommended Temperature Profile forfor Wave Soldering Wave Soldering
Preheat 100 Preheat 100 Seconds Max. Seconds Max. 250C 250C Soldering Soldering 10 Seconds Max. 10 Seconds Max. Natural Natural Cooling Cooling 230C 230C 200C 200C 150C 150C 60 Seconds Max. 60 Seconds Max. 150C 150C
Recommended Temperature Profile Recommended Temperature Profile forfor Reflow Soldering Reflow Soldering
Preheat 100 Preheat 100 Seconds Max. Seconds Max. Soldering Soldering 10 Seconds Max. 10 Seconds Max. Natural Natural Cooling Cooling
20 Seconds Max. 20 Seconds Max. 60 Seconds Max. 60 Seconds Max.
PAGE 6 OF 6 Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Spec ific ation s g iven herein m ay be cha nged a t any tim e w itho ut pr ior not ice. Pleas e c onf ir m te chnic al s pec if ica tions before you order an d/or u se.

▲Up To Search▲

Price & Availability of MCL2AJTTE100

	To Download MCL2AJTTE100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .